Top Sellers

Shop

Ebot IR sensor

The EBot IR sensor  scans IR signals in specific frequency ranges defined by standards and converts them to electric signals on its output pin (typically called signal pin). The IR signals are mainly used for transmitting commands over the air on short distances (typically few meters) like what you’ve already worked with on TV remote controls or other similar electronic devices.

  It only requires three connections. When it detects an obstacle within range it will send an output low.

Using Ebot IR sensors, Many projects can be done.

1.500 KWD Add to Cart

EBOT LCD

LCD modules are vey commonly used in most embedded projects, the reason being its cheap price, availability and programmer friendly. Most of us would have come across these displays in our day to day life, either at PCO’s or calculators. The appearance and the pinouts have already been visualized above now let us get a bit technical.

16×2 LCD is named so because; it has 16 Columns and 2 Rows. There are a lot of combinations available like, 8×1, 8×2, 10×2, 16×1, etc. but the most used one is the 16×2 LCD. So, it will have (16×2=32) 32 characters in total and each character will be made of 5×8 Pixel Dots. 

Now, we know that each character has (5×8=40) 40 Pixels and for 32 Characters we will have (32×40) 1280 Pixels. Further, the LCD should also be instructed about the Position of the Pixels. Hence it will be a hectic task to handle everything with the help of MCU, hence an Interface IC like HD44780is used, which is mounted on the backside of the LCD Module itself. The function of this IC is to get the Commands and Data from the MCU and process them to display meaningful information onto our LCD Screen.

5.0 KWD Add to Cart

EBOT LED Green

This is a bright green LED module. When you connect it to EBOT  board, after program, it can emit bright Green light. you can also control it using PWM. It will be like fireflies at night. You  can also combine it with other sensors to do various interesting interactive experiments.

1.00 KWD Add to Cart

EBOT LED Red

This is a bright Red LED module. When you connect it to EBOT  board, after program, it can emit bright Red light. you can also control it using PWM. It will be like fireflies at night. You  can also combine it with other sensors to do various interesting interactive experiments.

1.00 KWD Add to Cart

EBOT LED White

This is a bright White LED module. When you connect it to EBOT  board, after program, it can emit bright White light. you can also control it using PWM. It will be like fireflies at night. You  can also combine it with other sensors to do various interesting interactive experiments.

1.00 KWD Add to Cart

EBOT Light Sensor

Light Sensor is commonly seen in our daily life and is mainly used in intelligent switch, also in common electronic design.

It consist of Photocell, which is a semiconductor. It has features of high sensitivity, quick response, spectral characteristic, and R-value consistence, maintaining high stability and reliability in environment extremes such as high temperature, high humidity. It’s widely used in automatic control switch fields like cameras, garden solar lights, lawn lamps, money detectors, quartz clocks, music cups, gift boxes, mini night lights, sound and light control switches, etc.

1.500 KWD Add to Cart

EBOT music node with SD Card

The Music  node is built to make MP3 sound integration easier  with ebot.

it comes with SD card. So that the user can store different mp3 files and then can be used for the projects containing mp3.This node also comes with the USB jack. so that user can directly plug the node to the system to store the files.User can also use the node as SD card reader as well

When a USB micro  cable is connected to the music node the contents of the microSD card appears as a jump drive. Simply plug in the music node  and you'll be transferring MP3s, no need for drivers.

Sound output is provided via a 3.5mm headphone jack or poke-home connector allowing an external speaker to be connected without soldering.

5.00 KWD Add to Cart

EBOT potentiometer

A potentiometer is basically a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.

The measuring instrument called a potentiometer is essentially a voltage divider used for measuring electric potential (voltage); the component is an implementation of the same principle, hence its name.Potentiometers are commonly used to control electrical devices such as volume controls on audio equipment. Potentiometers operated by a mechanism can be used as position transducers, for example, in a joystick. Potentiometers are rarely used to directly control significant power (more than a watt), since the power dissipated in the potentiometer would be comparable to the power in the controlled load.

Ebot potentiometer consist of 3 pind namely S,V and G(signal, VCC and Ground respectively.)

1.500 KWD Add to Cart

EBOT relay

Relay is an electromagnetic device which is used to isolate two circuits electrically and connect them magnetically. They are very useful devices and allow one circuit to switch another one while they are completely separate. They are often used to interface an electronic circuit (working at a low voltage) to an electrical circuit which works at very high voltage. For example, a relay can make a 5V DC battery circuit to switch a 230V AC mains circuit. Thus a small sensor circuit can drive, say, a fan or an electric bulb.


A relay switch can be divided into two parts: input and output. The input section has a coil which generates magnetic field when a small voltage from an electronic circuit is applied to it. This voltage is called the operating voltage. The output section consists of contactors which connect or disconnect mechanically. In a basic relay there are three contactors: normally open (NO), normally closed (NC) and common (COM). At no input state, the COM is connected to NC. When the operating voltage is applied the relay coil gets energized and the COM changes contact to NO.

By using proper combination of contactors, the electrical circuit can be switched on and off.

2.00 KWD Add to Cart

EBOT RGB LED

The WS2812B (or "NeoPixel") may look like a common 5050-sized (5x5mm) SMD LED, but there’s actually an integrated control circuit embedded inside there too. If you look really hard, you can see the tiny black chip hidden in there, along with minuscule gold wires connecting the chip to the LED. This LED is certainly more than meets the eye! The 'B' at the end of the WS2812 name denotes that these specific LEDs are equipped with and only require FOUR pins instead of SIX!

The LED itself is unlike most RGB (Red/Green/Blue) LEDs. The brightness of each color can be adjusted using a serial string to one of 256 different levels. That means there are 16,777,216 (2563) possible combinations of colors. You can produce any color from white to black (off), or salmon to sienna.

Applications

  • Full-color module, Full color soft lights a lamp strip
  • LED decorative lighting
1.500 KWD Add to Cart

EBOT servo motor FUTABA - 360 degree

Futaba S3003 Servo Motor-360 Degree. The Futaba S3003 Plastic Geared Servo Motor is a decent servo for every hobbyist and electronics student. The powerful motor is PWM controlled for easy interfacing.

 

4.5 KWD Add to Cart

EBOT servo motor FUTABA -180 degrees

Futaba S3003 Servo Motor is a decent servo for every hobbyist and electronics student. The powerful motor is PWM controlled for easy interfacing with Ebot for various application and projects.

S3003 standard NIB servo for RC car plane. High torque analog servo. Stable and shock proof. Compliant with most standard receiver connector. Great for truck, boat, racing car, helicopter and airplane.

3.250 KWD Add to Cart

Ebot Stepper Driver

The Ebot stepper Driver is a simple to use stepper motor driver, compatible with ebot  that can output a digital 0 to 5V pulse . The Driver requires a 6V to 30V supply to power the motor and can power any voltage of stepper motor. The Ebot stepper Driver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control! EBot stepper

Driver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors

5.00 KWD Add to Cart

EBOT Temperature Sensor

EBOT temperature sensor uses LM35 Linear Temperature Sensor ,which based on semiconductor LM35 temperature sensor. It can be used to detect ambient air temperature. This sensor offers a functional range among 0 degree Celsius to 100 degree Celsius. Sensitivity is 10mV per degree Celsius. The output voltage is proportional to the temperature.

This sensor is commonly used as a temperature measurement sensor. It includes thermocouples, platinum resistance, and thermal resistance and temperature semiconductor chips. The chip is commonly used in high temperature measurement thermocouples. Platinum resistance temperature sensor is used in the measurement of 800 degrees Celsius, while the thermal resistance and semiconductor temperature sensor is suitable for measuring the temperature of 100-200 degrees or below, in which the application of a simple semiconductor temperature sensor is good in linearity and high in sensitivity. The  temperature sensor is very easy to use and compatible with Ebot and  Arduino shield.

 

1.500 KWD Add to Cart

EBOT touchpad

Ebot touchpad is designed for connecting various inputs,  up to 11 inputs. there are 11 terminals where you can connect aligator clips. no need of soldering.Using the aligator clips, you can connect the Fruits and makes the project funny with ebot.

 

You can also uses the touchpad as  directional input like UP,DOWN,LEFT  and RIGHT.

there is a slider section on the right side.

You can connect the touchpad with 3 wire connection to ebot.

 

6.00 KWD Add to Cart