Shop

SparkFun Motor Driver - Dual TB6612FNG (with Headers) (Genuine)

The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes: CW, CCW, short-brake and stop. The two motor outputs (A and B) can be separately controlled, and the speed of each motor is controlled via a PWM input signal with a frequency up to 100kHz. The STBY pin should be pulled high to take the motor out of standby mode. Due to popular demand, this version of the SparkFun Motor Driver includes pre-soldered male headers for ease of use. With the headers already soldered on, you can jump right in to using this little board without any assembly!

Logic supply voltage (VCC) can be in the range of 2.7--5.5VDC, while the motor supply (VM) is limited to a maximum voltage of 15VDC. The output current is rated up to 1.2A per channel (or up to 3.2A for a short, single pulse).

The board comes with all components installed as shown. Decoupling capacitors are included on both supply lines. All pins of the TB6612FNG are broken out to two 0.1" pitch headers; the pins are arranged such that input pins are on one side and output pins are on the other.

5.5 KWD Add to cart

Updated version of TB6600 Stepper Motor Driver 4A 9~42V TTL 32 Micro-Step CNC 1 Axis NEW 2 or 4 Phase of Stepper Moto 42, 57, 86

4A TB6600 Stepper Motor Driver Controller

9~42V TTL 16 Micro-Step CNC 1 Axis 2 or 4 Phase of Stepper Moto 42, 57, 86

NOTE:

It is Updated version of TB6600 4A Stepper Motor Driver the practicability of this type is same to TB6600 4A driver, But inside the apperance of it is different from TB6600 4A Stepper Motor Driver.

5 KWD Add to cart

 2PCS For arduino smart Car Robot Plastic Tire Wheel with DC 3-6v Gear Motor

This product is a DC gear motor +1 wheel = 1 piece

Package Included:

  • 2xsmart Car Robot Plastic Tire Wheel

  • 2x DC Gear Motor

 

 

2.5 KWD Add to cart

16 Channel 12-bit PWM/Servo Driver-I2C interface PCA9685

Want to make a hexapod walker? Maybe you're making a piece of art with tons of moving parts, or you need to drive a ton of LEDs with precise PWM output. Your microcontroller has a limited number of PWM outputs, and you find yourself running out! Not with the Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface. With this pwm and servo driver breakout, you can control 16 free-running PWM outputs with just two pins! Need to run more than 16 PWM outputs? No problem. Chain together up to 62 of these beauties for up to an outstanding 992 PWM outputs.

3 KWD Add to cart

Dc Stepper Motor Drive Controller Board Module Tb6612FNG Replace L298n

The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled, the speed of each motor is controlled via a PWM input signal with a frequency up to 100kHz. The STBY pin should be pulled high to take the motor out of standby mode.
 
Logic supply voltage (VCC) can be in the range of 2.7-5.5VDC, while the motor supply (VM) is limited to a maximum voltage of 15VDC. The output current is rated up to 1.2A per channel (or up to 3.2A for a short, single pulse). 
 
Board comes with all components installed as shown. Decoupling capacitors are included on both supply lines. All pins of the TB6612FNG are broken out to two 0.1" pitch headers; the pins are arranged such that input pins are on one side and output pins are on the other. 

2.5 KWD Add to cart

L298N motor driver board module L298 stepper motor smart car robot

L298N is a high voltage, high current motor driver chip. The chip uses 15-pin package. The main features are: high voltage, maximum operating voltage up to 46V; output current, instantaneous peak current up to 3A, continuous operating current of 2A; rated power 25W. Contains two H-bridge high-voltage and high current full-bridge driver can be used to drive DC motors and stepper motors, relays, coils and other inductive load; using standard logic level signal control; having two enable control terminal, in allows input signal without being affected or disable the device has a logic supply input, the internal logic circuit part of the work at a low voltage; can be an external sense resistor, the amount of change back to the control circuit. Drive motor using L298N chip, the chip can drive a two-phase stepper motors or four-phase stepper motor, can drive two DC motors.

3.5 KWD Add to cart

HY-DIV268N-5A Stepper driver

HY-DIV268N-5A drive using the drive's current loop subdivision control, the motor torque ripple is very small, low-speed running is very smooth. High-speed torque is much higher than other two-phase drive, high positioning accuracy. Widely used in the engraving machine, CNC machine tools, packaging machinery and other high resolution requirements on the device. 
 

9 KWD Add to cart

S3003 Servo 360 degree

Futaba S3003 Servo Motor-360 Degree

 

4.5 KWD Add to cart

MIcroservo 9g A0090-180 degrees

Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is very similar in size and specifications to the Hitec HS-55. This little guy is able to take in 6 volts and deliver 20.8 oz-in. of maximum torque at 0.10 sec/60°

4 KWD Add to cart

RMCS-1106 Micro-Stepping Motor Driver

RMCS-1106 is Rhino Motion Controls new and improved DSP based micro-stepping drive for 1.8deg Bipolar Stepper Motors. It is designed for smooth and quiet operation without compromising on torque and control at higher speeds. It has short-circuit protection for the motor outputs, over-voltage and under-voltage protection.

The RMCS-1106 achieves micro-stepping using a synchronous PWM output drive and high precision current feedback and this is absolutely silent when the motor is stopped or turning slowly. It virtually eliminates stopped-motor heating regardless of power supply voltage using a DSP based PID current control loop.

The RMCS-1106’s closed-loop control gains are calibrated on start-up based on motor characteristics and also adjusted dynamically while the motor is in motion. This control algorithm makes it capable of achieving better torque at higher speeds in comparison to comparable drives in its range.

The PULSE/STEP, DIRECTION and ENABLE inputs are optically isolated. The inputs work with 2.5V, 3.3V or 5V logic drive signals. The input drive current is 5mA at 2.5V so almost all logic family (74LS, 74HC, etc.) can be used to drive these inputs. Each input provides individual anode and cathode connections to the opto-isolator allowing for multiple input drive interfaces.

9 KWD Add to cart

JGA25-370 6V DC GEAR MOTOR

Excellent quality JGA25-370 Geared Motor 77 RPM. Great for robot building.

10 KWD Add to cart

HIGH TORQUE DC GEARED MOTOR 200RPM WITH DRIVER

This motor comes with a current controlled drive for Industrial grade high torque dc motor with various types of input signals. It supports UART/I2C/PPM/Analog signals directly for speed and direction control. The drive even works well at very low speeds.

The Motor is a Industrial grade 200RPM high torque motor with a massive torque of 32kgcm in small size. The motor has a metal gearbox with all high quality metal gears and has a off-centered shaft.

21 KWD Add to cart