Shop

Premium female to female Jumper Wires (40 pcs /set) -20 cm

These premium jumper wires are 20cm long and come in a ‘strip’ of 40 (4 pieces of each of ten rainbow colors). They have 0.1″ female header contacts on both end and fit cleanly next to each other on standard-pitch 0.1″ (2.54mm) header.

The best part is they come in a 40-pin ribbon cable. You can always pull the ribbon wires off to make individual jumpers, or keep them together to make neatly organized wire harnesses.

For best results, when plugging these in a line, have the sides with the ‘silver latch bit’ sticking out since that side is a tiny bit wider than 0.1″

0.500 KWD Add to cart

Premium female to female Jumper Wires (40 pcs /set) -10 cm

These premium jumper wires are 10cm long and come in a ‘strip’ of 40 (4 pieces of each of ten rainbow colors). They have 0.1″ female header contacts on both end and fit cleanly next to each other on standard-pitch 0.1″ (2.54mm) header.

The best part is they come in a 40-pin ribbon cable. You can always pull the ribbon wires off to make individual jumpers, or keep them together to make neatly organized wire harnesses.

For best results, when plugging these in a line, have the sides with the ‘silver latch bit’ sticking out since that side is a tiny bit wider than 0.1″

 

0.500 KWD Add to cart

Premium male to female Jumper Wires (40 pcs /set) -20 cm

These premium jumper wires are 20cm long and come in a ‘strip’ of 40 (4 pieces of each of ten rainbow colors). They have 0.1″ male and female header contacts on different  end and fit cleanly next to each other on standard-pitch 0.1″ (2.54mm) header.

The best part is they come in a 40-pin ribbon cable. You can always pull the ribbon wires off to make individual jumpers, or keep them together to make neatly organized wire harnesses.

For best results, when plugging these in a line, have the sides with the ‘silver latch bit’ sticking out since that side is a tiny bit wider than 0.1″

0.500 KWD Add to cart

Premium male to female Jumper Wires (40 pcs /set) -10 cm

These premium jumper wires are 10cm long and come in a ‘strip’ of 40 (4 pieces of each of ten rainbow colors). They have 0.1″ male and  female header contacts on different  end and fit cleanly next to each other on standard-pitch 0.1″ (2.54mm) header.

The best part is they come in a 40-pin ribbon cable. You can always pull the ribbon wires off to make individual jumpers, or keep them together to make neatly organized wire harnesses.

For best results, when plugging these in a line, have the sides with the ‘silver latch bit’ sticking out since that side is a tiny bit wider than 0.1″

0.500 KWD Add to cart

FTDI to USB cable

The FTDI cable is a USB to Serial (TTL level) converter which allows for a simple way to connect TTL interface devices to USB. The I/O pins of this FTDI cable are configured to operate at 5V.

The FTDI cable is designed around an FT232RQ, which is housed in a USB A connector. The other side of the cable is terminated with a 0.1" pitch, 6-pin connector with the following pinout: RTS, RX, TX, 5V, CTS, GND (RTS is the green cable and GND is black).

This cable has the same pinout and functionality as our FTDI Basic Breakout board; you can use it to program your Arduino ProPro Mini and Lilypad. For use with those boards, align the black and green wires of the FTDI cable with the 'BLK' and 'GRN' labels on the PCB.

There are pros and cons to the FTDI Cable vs the FTDI Basic. The FTDI Basic has great LED indicators, but requires a Mini-B cable. The FTDI Cable is well protected against the elements, but is large and cannot be embedded into a project as easily. The FTDI Basic uses DTR to cause a hardware reset where the FTDI cable uses the RTS signal.

5 KWD Add to cart

9V 2.1 x 5.5mm Male DC Plug to 9v battery Clip Cable

9V Battery Button clip Power Plug  white cable.

0.75 KWD Add to cart